RGP10A - rgp10m current: 1.0 a voltage range: 50 - 1000v verse current voltage drop symbol rgp 10a rgp 10b rgp 10d rgp 10g rgp 10j rgp 10k rgp 10m unit maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward current 0.375"(9.5mm) lead length ta = 55 c peak forward surge current, 8.3ms single half sine wave superimposed on rated load (jedec method) maximum peak forward voltage at i f = 1.0 a v f 1.3 v maximum full load reverse current, full cycle average 0.375",(9.5mm) lead length ta = 55 c maximum dc reverse current ta = 25 c i r 5.0 m a at rated dc blocking voltage ta = 150 c i r(h) 200 m a maximum reverse recovery time ( note 1 ) trr 150 250 500 ns typical junction capacitance ( note 2 ) c j 15 pf typical thermal resistance ( note 3 ) r q ja 50 c/w junction temperature range t j - 65 to + 175 c storage temperature range t stg - 65 to + 175 c notes : ( 1 ) reverse recovery test conditions : i f = 0.5 a, i r = 1.0 a, irr = 0.25 a. ( 2 ) measured at 1.0 mhz and applied reverse voltage of 4.0 v dc ( 3 ) thermal resistance from junction to ambient at 0.375" (9.5mm) lead lengths, p.c. board mounted. i r(av) a a m a 100 i f(av) i fsm 30 1.0 features high current capability high reliability low re low forward fast switching for high efficiency 1 of 2 www.sunmate.tw fast recovery rectifier diodes maximum ratings and electrical characteristics t a = 25 c unless otherwise specified single phase, half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20%. characteristic case: do-41molded plastic ! ! terminals: plated leads solderable per mil-std-202, method 208 ! polarity: cathode band ! weight: 0.34 grams (approx.) ! mounting position: any ! marking: type number mechanical data a a b c d dim min max a 25.40 b 4.06 5.21 c 0.71 0.864 d 2.00 2.72 all dimensions in mm do-41
2 of 2 rating and characteristic curves ( rgp10 a - rgp10m ) fig.1 - reverse recovery time characteristic and test circuit diagram + notes : 1. rise time = 7 ns ma x ., input i mpedance = 1 megaohm, 22 pf. 2. rise time = 10 ns ma x., source i mpedance = 50 ohms. 3. all resistors = non-inductive types. fig.2 - derating curve for output fig.3 - maxi mum non-repetitive peak rectified current forward surge current 0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100 ambient temperature, ( c) number of cycles at 60hz fig.4 - typical forward characteristics fig.5 - typical reverse characteristics 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 for ward voltage, volts 60hz resistive or inductive load 0.375" (9.5mm) lead lengths 0.8 0.6 0.4 0.2 1.0 10 1.0 24 0 30 0 18 12 6 0.1 10 80 0.01 0.01 1.0 0.1 100 140 0 20 40 60 120 percent of rated reverse voltage, (%) peak forward surge current, amperes average forward output current, amperes forward current, amperes reverse current, microamperes t j = 25 c t j = 100 c t j = 25 c pulse w idth = 300 m s 2% duty cycle 8.3 ms single half s ine- wave (jedec) method t j = t j ma x. set time base for 50/100 ns/cm trr + 0.5 0 - 0.25 - 1.0 a 1 oscilloscope ( note 1 ) 1 w 50 w 10 w d.u.t. 50 vdc (approx.) pulse generator ( note 2 ) t j = 25 c www.sunmate.tw
|
